Henan Lianghe Pipeline Equipment Co.,Ltd
Henan Lianghe Pipeline Equipment Co.,Ltd
Add to Cart
Product Introduction
A large tie rod type corrugated compensator is a device used to compensate for lateral and angular displacements in piping systems, usually consisting of components such as pipes, bellows, and large tie rods. Its main function is to compensate for the lateral displacement and angular displacement of the curved pipeline, and at the same time bear the internal pressure thrust to protect the safe operation of the pipeline system.
Product structure features
The large tie rod type corrugated compensator consists of two identical bellows and end tubes, end plates and tie rods. The bellows absorb the lateral displacement of a single or multi-plane pipe by means of an angular offset. 4 large tie rods can withstand internal pressure thrust and other additional external forces, after the compensator works deformation, the large tie rod can play a role in limiting the deformation to protect the bellows.
Product application scenarios
Large tie rod corrugated compensator is widely used in chemical, environmental protection, food cleaning, engineering construction water supply and drainage and other industries, and can transport various corrosive substances in the temperature range of -20°C to 150°C. Its stiffness and compression strength are better than those of traditional plastic hoses, and it is suitable for a wide range of pressure environments.
Product parameters
| No | Name | Material |
| 1 | Flange | Carbon steel or stainless steel 304,316,321,etc. |
| 2 | Tie rod | Carbon steel or stainless steel 304,316,etc. |
| 3 | Internal Sleeve | Stainless steel 304,316. |
| 4 | Bellows | Stainless steel 304,316,321,etc. |
| 5 | Nut | Carbon steel or stainless steel 304,316,321,etc. |
| 6 | End pipe | Carbon steel |
| DN | Wave number |
Pressure leave
| Axial compensation,rigidity | Maximum outer diameter size | |||
| Product length | |||||||
| 1200 | 1500 | 2000 | 2500 | ||||
| 100 | 4+4 | 0.25 | 177.2/2.2 | 243/1.2 | 354/0.6 | 465/0.3 | 310 |
| 0.6 | 177.2/2.2 | 243/1.2 | 341/0.6 | 447/0.3 | 310 | ||
| 1.0 | 163/2.2 | 224/1.2 | 325/0.6 | 427/0.3 | 310 | ||
| 1.6 | 91/4 | 127/2 | 187/1 | 247/0.6 | 310 | ||
| 2.5 | 94/8 | 132/5 | 194/2 | 256/1 | 310 | ||
| 125 | 4+4 | 0.25 | 181/2.8 | 251/1.5 | 369/0.7 | 487/0.4 | 360 |
| 0.6 | 172/2.8 | 239/1.5 | 351/0.7 | 463/0.4 | 360 | ||
| 1.0 | 161/2.8 | 224/1.5 | 330/0.7 | 435/0.4 | 360 | ||
| 1.6 | 99/11 | 140.6 | 209/3 | 277/2 | 360 | ||
| 2.5 | 99/11 | 113/6 | 197/3 | 262/2 | 360 | ||
| 150 | 4+4 | 0.25 | 199/6 | 278/3.2 | 410/1.6 | 542/1.0 | 410 |
| 0.6 | 186/6 | 259/32 | 382/1.6 | 506/1.0 | 410 | ||
| 1.0 | 122/10 | 170/6 | 251/3 | 332/2 | 410 | ||
| 1.6 | 108/12 | 15/36 | 230/3 | 307/2 | 410 | ||
| 2.5 | 82/22 | 117/12 | 176/5 | 234/3 | 410 | ||
| 200 | 4+4 | 0.25 | 155/9.4 | 220/4.9 | 327/2.25 | 435/1.4 | 480 |
| 0.6 | 138/9.4 | 196/4.9 | 291/2.25 | 388/1.0 | 480 | ||
| 1.0 | 101/20 | 143/11 | 213/5 | 283/3 | 480 | ||
| 1.6 | 75/42 | 108/21 | 164/10 | 220/6 | 480 | ||
| 2.5 | 59/69 | 86/35 | 130/16 | 176/9 | 480 | ||
Product installation and maintenance
1. Pre-installation inspection: After the compensator arrives, it is necessary to check whether the signage, certificate, model, specification and technical parameters are consistent, the appearance is free of scratches or sharp indentations, there is no foreign matter inside, and the connection port is intact.
2. Hoisting and transportation: Special fixtures or lifting lugs should be used when hoisting, and it is strictly forbidden to use transport tie rods as load-bearing parts. During transportation and storage, it is necessary to prevent sun and rain, water immersion, harmful gas corrosion, and avoid falling and collision.
3. Medium requirements: The chloride ion content of the medium should be less than or equal to 25PPM, it is strictly prohibited to splash the bellows with welding slag, it must be installed according to the product flow direction sign, and the guiding support and fixed support are reasonably set .
Product Applications
FAQ
Q: Can you provide drawings and technical data?
A: Yes, You can send us your request. our professional technical department will design and provide drawings and techical data.
Q: Have your products been exported?
A: Yes, they have been exported to USA, France, Australia, Peru, Chile, Brazil, Uruguay, Russia, UAE, Saudi Arabia, Oman, Egypt, Serbia, Vietnam, South Korea, Indonisia, India, Thailand, Pakistan, Philippines, Singapore, HK...
Q: What is the operating pressure of this product?
A: PN6,PN10,PN16,PN25.
Q: Can I choose a product made of different materials?
A: Of course, we have carbon steel, stainless steel, which can be made according to customer requirements.
Q: Can the length of the large tie rod transverse corrugated compensator be customized?
A: Of course, we have many different specifications and models of molds, which can be customized according to your length.
Q: Do you provide samples? Is it free or charged?
A: Yes, we can offer sample free but shipping charges covered by customer.